Оглавление
How to Manage Heat in PCBs: Techniques, Materials & Best Practices
This article was originally published in Feb 2024 and last updated on June 29, 2026.
Выделение тепла в печатных платах
Активные компоненты:
- Microprocessors and Central Processing Units (CPUs): Highly consuming electrical power and performing intensive processing operations lead to production of high amounts of heat.
- Силовые транзисторы: Used for amplification and power control purposes, producing large amounts of heat.
- Light-Emitting Diodes (LEDs): Produce high-intensity lights for illumination purposes; produce large amounts of heat.
- Memory Modules: Produce heat due to their high-speed operation during read and write processes.
Пассивные компоненты:
- Резисторы: Conversion of electrical energy to heat energy, particularly in high-power resistors.
- Inductors/Трансформеры: Core and winding losses resulting in heat dissipation.
- Конденсаторы: Dielectric losses in high-frequency capacitors result in heat dissipation.
Разъемы и межсоединения:
- Сильные токовые дорожки: Трассы и разъемы, по которым протекают большие токи, выделяют резистивное тепло.
- Термические виасы: Although the original intention of via design is heat dissipation, if designed improperly, the vias themselves can also generate heat.
Key Factors Influencing Heat Generation
| Factor | Impact on Heat Production |
| Потребляемая мощность | Higher power levels directly increase heat production |
| Operational Frequency | Higher frequencies increase switching losses |
| Плотность компонентов | Dense placement causes local hot spots |
| Trace Width/Thickness | Narrow or thin traces have higher resistance |
| Duty Cycle | Continuous operation causes more heat buildup than intermittent use |
| Ambient Conditions | Temperature, humidity, and airflow affect heat dissipation |
| Voltage/Current Levels | Higher levels increase power dissipation |
| Целостность сигнала | Poor signal integrity causes additional power loss |
Последствия плохого терморегулирования
- Thermal Runaway: As the temperature of the component increases, its power consumption rises, thus causing an uncontrollable destruction of the component. The self-propelled process may destroy the component within only a few seconds.
- Сигнал Distortion: High temperatures may change the electrical properties of the materials of the printed circuit board and may cause changes in the импеданс.
- Shortened Lifespan of Components: According to the Arrhenius equation, each increase in the operational temperature by 10 degrees will shorten the lifetime of the semiconductor component twice.
- Mechanical Stress and Warping: Different thermal expansion coefficients of the materials (медь, FR-4, etc.) cause mechanical stress that, in its turn, causes solder joint failure, delamination, and warping.
- Product Recall and Brand Deterioration: In the most severe case, thermal failures at the site may result in product recalls and brand deterioration that is important for any electronics producer.
Thermal Management Principles: Heat Transfer in PCBs
Проведение
Конвекция
Радиация
PCB Material Selection for Thermal Performance
Thermal Conductivity Comparison
| Материал | Теплопроводность (Вт/м-К) | Типичные области применения |
| FR-4 (Standard) | 0.3-0.4 | General consumer electronics |
| FR-4 (High-Tg) | 0.3-0.4 | Industrial, automotive (up to 170°C Tg) |
| Полиимид | 0.1-0.4 | Flexible PCBs, high-temperature environments |
| Rogers Materials | 0.5-1.0 | RF and microwave applications |
| Aluminum MCPCB | 1-5 | LED lighting, power electronics |
| Alumina (Al₂O₃) Ceramic | 24-30 | High-power RF, thick-film circuits |
| Aluminum Nitride (AlN) Ceramic | 170-230 | High-performance power modules, extreme power density |
| Copper (Reference) | ~385 | Thermal planes, heat spreaders |
How to Choose the Right Substrate Material
- Power Levels: Circuits with power levels less than 5W need FR-4. If the circuit has medium power levels (5-50W), then it requires MCPCB или high-Tg FR-4. If the power level is more than 50W, then нитрид алюминия или керамическая подложка рекомендуется.
- Temperature of Operation: Glass transition temperature of standard FR-4 is 130-140°C. If the operating temperature is higher than 90-110°C, then high-Tg FR-4 or polyimide material рекомендуется.
- Frequencies Needed: In case of RF and microwave frequencies, you will have to choose Материал Rogers.
- Mechanical Requirements: Polyimide is needed for flexible designs while metal core or ceramic substrates can be helpful for rigid designs.
5 PCB Thermal Management Techniques
- Тепловой Vias: Small holes within a PCB that enable heat distribution.
- Heat Sink: Heat sink is a device with fins for increasing surface area to dissipate heat.
- Системы охлаждения: These involve air or liquid cooling.
- Thermal Interface Material (TIM): This is any material that enhances heat dissipation from component to heat sink.
- Thermoelectric Cooler (TEC): This is any device providing cooling for a particular component.
Тепловые проходы: Дизайн и реализация
Лучшие практики проектирования тепловых сетей
- Diameter: Drill size should normally be no larger than 8 mils (0. 2 mm) to avoid solder wicking. Usually, a 0. 5 mm drill diameter and a roughly 0. 4 mm finished hole size are used.
- Расстояние между ними: Position the vias such that the distance between them is around 1. 2 to 1. 5 of their diameter. If the placement is very close, then you may be in danger of damaging the board physically, and if too far apart, then heat dissipation may not be efficient.
- Via Filling: For heat dissipation purposes, copper-filled vias are ideal. Normally, simple plated vias are fine though not as good. A solder fill may be helpful but definitely inferior to copper.
- Количество отверстий: Place a sufficient number of thermal vias under heat-generating parts to equally spread out the heat. Thermal resistance is inversely proportional to the number of vias.
- Proximity to Planes: Make the via barrel as close as possible to the copper planes to help heat conduction.
Heat Sinks: Passive vs. Active
- Пассивные радиаторы: Dissipate heat only through natural convection and radiation. Typically made from metals with very good thermal conductivity like алюминий, or copper, they often feature multiple fins to provide a heat transferring surface area that is greater than the one of a larger block of the cooling material. Besides being more straightforward and reliable (because it has no moving parts), passive heat sinks are also less expensive to manufacture and maintain.
- Активные радиаторы: Besides the heat sink itself, they incorporate parts like fans or blowers that help throw heat away from the sink by forced air, that is, forced convection. Many good things come with active heat sinks like being highly efficient, but at the same time, they are more complicated, more expensive and even can fail at the level of their moving parts (fans).
How to Include Heat Sinks in Your PCB Design
- Method of attachment: For through-hole components, you can use spring clips; for surface-mount devices, adhesives or thermal tape can come in handy; and for the larger components, screw-mounted brackets. Make sure that the clamping pressure is sufficient for intimate thermal contact.
- Mechanical очистка: Make sure the fin height and airflow paths have enough room. Also, the components upstream should never block the airflow.
- The right position: Passive heat sinks will perform best if the fins are vertical, since this allows the air to flow freely. A horizontal arrangement of fins will cause a loss of efficiency in the natural convection process.
- Provide mechanical support to ПЕЧАТНАЯ ПЛАТА: A heavy heat sink gets supported very well if the weight is directly transferred to the chassis through mounting holes with standoffs. Without this, strain on solder joints is inevitable.
- Electrical очистка: Ensure that creepage and clearance distances meet стандарты МПК. Where electrical isolation is needed, insulating pads are necessary.
Системы охлаждения для печатных плат: воздушное охлаждение против жидкостного охлаждения
- Air Cooling: Involves moving fans or blowers to change the air over the PCB in expectation to heat dissipation. It is a straightforward, cost-effective, and highly used method. Even so, air cooling might not be effective enough for applications with very high power or very densely packed assemblies.
- Жидкостное охлаждение: It is the practice of transporting a liquid coolant through pipes or channels for heat removal. In that case, liquid cooling is more effective and is the right choice for high-power or high-density PCBs; Still, liquid cooling is more complicated, costly, and needs careful leak prevention.
Designing Efficient Cooling Systems for PCBs
- Airflow management: Keep vents for intake and exhaust open. Try to avoid recirculation. If necessary, use ducting to direct airflow across critical components.
- Coolant selection: Water-glycol mixtures have very good heat capacity but need corrosion inhibitors. Dielectric coolants are the best choice when the short-circuit risk is to be eliminated.
- Размещение компонентов: In case of air-cooled boards, locate the highest-power components closest to the air intake. When it comes to liquid-cooled boards, reserve cold plates for just the highest-dissipating components; the rest of the devices (of lower power) remain air-cooled.
- Redundancy and safety: To make sure that, in case of a failure of one cooling unit, the system will still be operational, consider redundant fans or pumps for high-availability systems. Don’t forget to add temperature sensors and thermal shutdown circuitry.
Материалы для тепловых интерфейсов (TIM)
- Термическая смазка: This kind of material has superb thermal conductivity capabilities but it can be a bit untidy and tricky to work with.
- Тепловой Колодки: Besides being simpler to use compared to grease, the thermal conductivity of these is also pretty good.
- Phase Change Materials (PCM): These are initially in the solid state and at room temperature. Once heated, they liquefy and fill the hollows, thereby providing a high level of thermal conductivity.
- Термоклеи: Apart from thermal conductivity, these also provide a form of mechanical attachment.
Applications and Selection Criteria in PCB Design
- Thermal capability: For components with low power output (< 2 W), thermal pads will suffice. But, for high-power components (> 10 W), thermal grease or PCMs will be the best choice as they offer the lowest thermal resistance.
- Mechanical aspects: If the surfaces are very uneven, one should use grease or PCMs, which can flow into the gaps. For flat surfaces with well-controlled clamping, pads are enough.
- Assembly & production: Pads are quicker and more amenable to mass production. Occasionally, the use of grease may require a dispensing step that needs to be controlled and will add to the process time.
- Reworkability: It is still possible to remove components that have been attached with grease or pads; while reworking components attached with adhesives or PCMs is quite a challenge.
- Thermal cycling stability: Usually the pads and PCMs perform better for stability when exposed to repeated temperature changes against silicone greases.
- Electrical insulation: When the components have exposed electrical pads, non-conductive TIMs should be the choice.
Thermoelectric Coolers (TECs)
TECs Applications in PCB Design
- Hot-side cooling: Equip the hot-side with a heatsink, and often also a fan, to be able to dissipate not only the pumped heat but also the electrical power consumed by the TEC. The heatsink has to be sized based on the total thermal load which will be bigger than the component’s own dissipation.
- Монтаж: The TEC has to be sandwiched between the component and the heatsink, with the clamping pressure being just right; too little will raise the thermal resistance and too much can cause the ceramic plates to crack.
- Источник питания: A constant DC current source should be provided; current ripple is an efficiency killer.
- Condensation risk: When the cold side is below the dew point, water droplets may form. In case the environment is humid, конформное покрытие or a sealed enclosure might be considered.
How to Choose the Right Thermal Management Strategy
| Power Level | Space Constraints | Recommended Strategy |
| < 5W | Ample | Natural convection + passive heat sink + standard FR-4 |
| 5-50W | Умеренный | Forced air cooling + thermal vias + MCPCB or high-Tg FR-4 |
| > 50W | Tight | Liquid cooling / heat pipes / vapor chamber + ceramic substrate |
| Localized Hot Spots | Any | TEC for precision cooling + thermal via arrays |
| Cost-Sensitive | Any | FR-4 + optimized layout + adequate copper weight (≥2 oz for high-current paths) |
Decision Flow
- Calculate Total Power Dissipation: Estimate the overall power dissipated by all the компоненты на печатной плате.
- Find Heat Flux Density: Divide the total power by the area of the board to get W/cm²
- Consider Space Constraints: Find out how much space there is for placing heatsinks, fans, or other cooling equipment.
- Decide on the Субстрат Материал: FR-4 for low power, MCPCB for medium power, ceramic/AlN for high power.
- Identify the Corresponding Cooling Method: Passive, active air, or liquid cooling given power density.
- Simulate and Confirm: Employ thermal simulation to check the design before making a prototype.
- Create a Prototype and Conduct Tests: Confirm with real thermal measurements (thermocouples, thermal imaging).
PCB Layout Strategies for Optimal Heat Dissipation
Component Placement and Spacing
- Separate the Heat Generating and Heat Sensitive Components: For example, make sure that the crystal oscillator, analog front-end, and accurate voltage reference should be placed far away from the high-power components that generate heat.
- Locate the High Power Components at the Edge of the Circuit Board: Not only does it make the process of transferring the heat to the surrounding environment easier, but it also facilitates the air flow.
- Proper Component Spacing: As heat is generated where there are dense components, it makes sure that the heat is dissipated properly. That is why it is necessary to maintain proper spacing between the components.
- Air Flow Direction: In case when the cooling is done by forced air, then it is essential that the high-power components should be placed in the area from where the air is flowing, while heat-чувствительные компоненты should be located where the air flows towards.
Thermal Zones and Isolation
- Thermal Zone Development: Division of the PCB into thermal zones based on the quantity of heat generated by each part is an excellent method for carrying out the cooling process. Each thermal zone can be cooled using a unique cooling process.
- Тепловые барьеры: Application of thermal barriers is an excellent way of segregating regions which have varied thermal characteristics. This ensures that heat generated in one thermal zone does not reach other thermal zones.
- Тепловая изоляция: In case there is heating and cooling regions in adjacency, you can install thermal isolation slots between them.
Copper Pour and Heavy Copper Design
- Use Copper Planes for Heat Dissipation: large copper surfaces (power and ground planes) should be regarded as heat dissipation devices – they help dissipate heat from hot components to other board areas.
- Think About Тяжелая медь: PCBs having copper layers of 2 oz and higher (these are heavy copper PCBs) are great for both thermal management and current handling capabilities. Heavy copper PCBs (3-4 oz and above) can handle high current levels and are good for heat dissipation.
- Thermal relief pads: In order to ensure that the heat generated by the components does not travel through the copper planes and result in high thermal resistance, thermal relief pads should be used. The solder joint may be one of the potential points of failure when assembling PCB. Thermal relief pads help avoid cracks.
Common PCB Thermal Management Mistakes to Avoid
- Insufficient or Absent Thermal Interface Material
- Problem: Small pockets of air between component and heatsink cause high thermal resistances.
- Solution: The right type of TIM should always be used between overheating components and heatsinks. The proper design of TIM could decrease thermal resistance to 5-6° C.
- Failure to Consider Thermal Via Filling
- Problem: Thermal vias filled with air have very high thermal resistance since there is air in them.
- Solution: Use copper filled or plated vias for maximum thermal conductivity.
- Ignoring Ambient Operating Conditions
- Problem: Designs that are tested at room temperature fail when ambient temperature is higher.
- Solution: The thermal analysis should consider the limits in temperature, humidity and air speed.
- Arrangement of Several Power Units
- Problem: Positioning of several high-power components causes overheating in certain areas.
- Solution: Distribute high-power components across the board and take into account ventilation.
- Dependency Only on Simulation, No Physical Validation
- Problem: Condition for boundaries in simulation can differ from those in reality.
- Solution: Thermal simulation has to be followed by practical testing of the прототип using thermocouples or thermal cameras.
- Inhomogeneous Copper Distribution in Interior Layers
- Problem: Non-homogenous distribution of copper results in thermal stresses and distortion of PCB.
- Solution: Homogenous copper distribution has to be achieved using copper balancing.
- Ignoring Thermal Properties of Solder Joints
- Problem: High concentration of voids in solder joints under thermal pads reduces thermal conductivity.
- Solution: Volume and process of reflow of паяльная паста has to be optimized to minimize voids.
- Overengineering without cost-benefit analysis
- Problem: Using sophisticated cooling methods for low-power components means wasting money.
- Solution: Thermal solution should match thermal demands.
Thermal Simulation Tools for PCB Design
ANSYS Icepak:
- Advanced software product for thermal simulation of electronic products based on CFD.
- Enables one to perform various simulations of heat transfer methods, including conduction, convection, and radiation.
- May be integrated with other products from ANSYS to conduct multiphysics analysis (thermal-stress coupling).
- Allows representing quite complicated configurations and detailed models of single components.
- Primarily designed for electronics with high power level, automotive and consumer electronics.
Mentor Graphics FloTHERM:
- Specialized thermal simulation software for electronic products.
- Extensive databases of components with numerous thermal parameters of components.
- Easy-to-use graphical user interface and all operations are made using drag-and-drop mechanism.
- Provides air flow, temperature and heat dissipation of components, boards and whole systems.
- Ideal solution for working on design and optimization of PCB, server and data center cooling systems.
SolidWorks Thermal Simulation:
- The Thermal Analysis comes naturally integrated into the SolidWorks CAD software.
- It helps in carrying out thermal, structural and fluid flow analyses.
- Design Optimization using Parametric studies.
- Perfect choice for thermal analysis of mechanical assemblies, electronic assemblies, and printed circuit boards.
When to Simulate vs. When to Prototype
- With simulation, you gain an important advantage in the initial stages of design as it allows to compare different alternatives and optimize your layout. Moreover, it simulates different scenarios on time and on budget.
- Prototype nowadays becomes a necessary step for final verification. Accuracy of simulation depends upon accuracy of the input data-material properties, boundary conditions and component models.
- Most Likely Scenario: Simulation would become a basis for making design choices and eliminating less effective solutions, but eventually you would have to prototype the real product to get the minimum cost and maximum confidence.
Стандарты и правила терморегулирования
Заключение
Need Expert Assistance with Your PCB Thermal Management Challenges?
Our engineering team provides complete PCBA thermal management solutions, covering material selection, thermal simulation, prototype development, and high-volume manufacturing. Whether you're developing products for автомобильный, медицинский, industrial automation, or бытовая электроника, we help solve complex thermal challenges and improve long-term product reliability.
FAQs about PCB Thermal Management
Похожие блоги
Table of Contents PCBA Functional Testing (FCT): A Complete Guide to Ensuring Board Reliability Published on May 9, 2023 · Updated on November 6, 2026
Table of Contents IPC Class 2 vs Class 3: Acceptance Criteria, Cost Impact, and How to Choose IPC Class 2 and Class 3 are the
Table of Contents Ventilator PCB Assembly: ISO 13485, IPC Class 3 & FDA QMSR-Ready Manufacturing Published on June 24, 2022 · Updated on October 30,
Table of Contents Ventilator PCB Assembly: ISO 13485, IPC Class 3 & FDA QMSR-Ready Manufacturing How is air delivered steadily with the help of ventilators,
Table of Contents Design Rule Checking in PCB Design: From Altium DRC to SMT Assembly Published on September 10, 2024 · Updated on October 22,
Table of Contents Automotive PCB Assembly: The Complete 2026 OEM Guide Failure of a consumer good is a warranty claim. Failure of an automotive printed
Сотрудничайте с FS Technology и получите профессиональное обслуживание печатных плат.