Оглавление

Solder Paste in PCB Assembly: Selection, Printing, Defects & Expert Tips

This article was originally published in Jan 2023 and last updated on July 19, 2026.

A crucial component in electronic devices is the PCBA board, consisting of two main parts: ПЕЧАТНАЯ ПЛАТА и Компоненты. The PCB supports and connects the components, which, in turn, provide the actual functionality. Initially, these two parts are separate, but through the assembly and soldering process, they are eventually combined into a unified whole.
 
In this assembly process, the use of certain key materials is necessary, and one of these is паяльная паста. This article will provide a detailed overview of the role of solder paste and a guide on how to correctly use solder paste in the Процесс сборки печатной платы.
Solder Paste in SMT Assembly

What is Solder Paste and Why Use it?

One of the most reliable methods to connect two metals without melting them is soldering, and solder paste is essential for achieving this. Паяльная паста is a special metal alloy composed of metal solder particles and a unique combination of flux. During the soldering process, the distinctive properties of solder paste allow it to melt and form a permanent bond, thus establishing a reliable connection between metals.
 
To ensure good performance during the soldering process, solder paste must meet several important standards:
  1. Low Melting Point: Given the heat sensitivity of the components, it should have a low melting point. In case the melting point is too high, there could be a possibility of the components being subjected to the maximum possible heat before completely melting.
  2. High Conductivity: It serves the purpose of not only making physical contact but also providing the electrical connection to enable the free flow of electrical current through the components.
  3. Compliant to RoHS Directive: The use of solder paste should be done such that it complies with the strict guidelines set by the Директива RoHS.
 
In the past, approximately 40% of solder pastes in electronic manufacturing consisted of a combination of lead and tin. However, due to the environmental hazards associated with lead, and with advancements in technology and increased environmental awareness, the производство электроники industry has gradually transitioned to lead-free processes. Consequently, lead-free solder paste has become the mainstream choice, reflecting a positive response to environmental concerns and industry focus on health and sustainability.
Печать паяльной пастой во время сборки печатной платы

Solder Paste Type: Particle Size, Flux & Alloy

Использование высококачественной и правильной паяльной пасты - важнейший шаг в обеспечении качества плат PCBA. Для проектов по сборке FS Technology предлагает различные марки и типы паяльных паст, отвечающие различным требованиям. Вы можете сделать выбор в зависимости от материалов, планируемых к пайке, и потребностей, или выбрать в соответствии с размером шариков припоя в паяльной пасте.

By Particle Size (Powder Type)

Чтобы соответствовать требованиям различных проектов, паяльные пасты обычно делятся на различные марки и категории. Эти классы основаны не только на точном размере шариков припоя, но и на том, что около 80% шариков припоя попадают в определенный диапазон размеров. Ниже приведены различные марки и соответствующие им размеры шариков припоя.

Марка паяльной пасты

Размер частицы

Тип 1

от 75 мм до 150 мм

Тип 2

от 45 мм до 75 мм

Тип 3

от 25 мм до 45 мм

Тип 4

от 20 мм до 38 мм

Тип 5

от 10 мм до 25 мм

Тип 6

от 5 мм до 15 мм

Тип 7

от 2 мм до 11 мм

Тип 8

от 2 мм до 8 мм

Совет профессионала:
For standard SMT assembly with 0603 components and 0.4mm pitch ICs, Type 4 solder paste (20-38μm) is the most versatile and widely recommended choice. For ultra-fine pitch applications like 01005 components, Type 5 or finer is required.

By Flux Type

Помимо учета размера частиц, выбор подходящей паяльной пасты на основе типа флюса также является приемлемым вариантом. Различные типы Поток печатной платы может лучше сочетаться с конкретными составами паяльных паст для достижения лучших результатов пайки или удовлетворения специфических технологических требований. Однако не все среды позволяют использовать этот тип флюса, и необходимо убедиться, что среда достаточно чистая.
  • Водорастворимая флюсовая паста: Состоит из органических компонентов и этиленгликолевой основы. Остатки водорастворимого флюса можно легко удалить с помощью легкодоступных на рынке чистящих средств.
  • Паяльная паста No-Clean: Этот тип паяльной пасты обычно используется при изготовлении неочищаемого флюса. Он имеет относительно низкое содержание твердых остатков и смол. Основное преимущество использования неочищаемого флюса - потенциальная экономия средств на очистке.
  • Паяльная паста на основе канифоли: Подобные паяльные пасты изготавливаются на основе канифоли и после пайки могут быть очищены с помощью растворителей.

By Alloy Composition

Whereas the original passage is concerned about the size of particles, the choice of alloy is just as important. The selection of alloy will determine the melting temperature, mechanical strength, and reliability of the solder joint.
  • SAC305 (Sn96.5/Ag3.0/Cu0.5): Industry standard for lead-free soldering applications. Provides the optimal combination of cost, thermal fatigue resistance, and wetting properties, thus suitable for all general-purpose applications such as automobiles and industrial electronics.
  • Low Temperature Alloys (for example, Sn-Bi): Used for components that require low temperature or when secondary reflow is necessary, with primary solder joints remaining intact.
  • High Reliability Alloys: Sometimes containing additional elements such as Nickel or Bismuth to improve drop shock and creep resistance, critical for аэрокосмическая промышленность и медицинский devices.

How to Select the Right Solder Paste for Your PCBA Project?

The selection of an appropriate type of solder paste is not universal. In order to have a high yield rate and reliability, you need to consider your project based on the following criteria. Please use the decision guide together with the technical information above.
Project FactorRecommended Solder Paste CharacteristicsRationale
Component Density & MiniaturizationFor high-density boards with 0201/01005 components and <0.4mm pitch BGAs, choose Type 4 or Type 5 powder with fine particle size.Finer powders ensure better print release and prevent clogging in narrow apertures, reducing the risk of insufficient solder.
Product Reliability RequirementsFor automotive, medical, or aerospace applications, opt for ROL0 (low-activity) no-clean flux combined with SAC305 or high-reliability alloys.Low-activity flux leaves minimal ionic residues, preventing electrochemical migration. High-reliability alloys offer superior thermal cycling and shock resistance.
Production Volume & MixFor high-mix, low-volume or prototype runs, Jet Printing with a fluid solder paste offers flexibility. For mass production, stencil printing with Type 4 paste is cost-effective.Jet printing eliminates stencil costs and allows quick changeovers. Stencil printing provides high throughput for repetitive jobs.
Соответствие нормативным требованиямIf your products are exported to EU or North America, ensure the solder paste is RoHS-compliant (lead-free). For medical implants, also consider biocompatible alloys.Non-compliance can lead to legal barriers and market rejection.
Process Window & EquipmentMatch the paste’s viscosity to your printing equipment (squeegee speed, pressure). Also, ensure your reflow oven can handle the recommended temperature profile.Incompatible viscosity causes smearing or insufficient release. Wrong profile leads to cold joints or component damage.
Recommendation from FS Technology:
In case of general electronics applications such as consumer and industrial controls, which account to about 80%, we advise the use of SAC305 Alloy in combination with Type 4 and No-clean ROL1 Flux, as it offers the most reliable solution at an affordable price. For specific needs, our engineering team is available for personalized consultation.

Best Practices for Solder Paste Storage and Handling

Solder Paste Storage in FS TECH
В зависимости от температуры и влажности в помещении завод PCBAХраните эти готовые к использованию паяльные пасты в специально разработанной упаковке, которая поддерживает температуру продукта между 0° и 30 °C (86 °F и 84 °F) в течение как минимум 48 часов.
 
Паяльную пасту следует доставлять в течение ночи или охлажденным транспортом. В летнее время транспортировка должна осуществляться по возможности ночью, чтобы сократить время и избежать высоких температур. Упаковка пасты может включать холодные пакеты, которые приходят тающими. Если 48-часовое время в пути не превышено, это типично и не является признаком повреждения или ненадлежащего обращения. По прибытии паяльная паста должна быть сразу же перемещена на контролируемое хранение. Рекомендуется, но не всегда необходимо, использовать холодильное оборудование.
 
Detailed Storage Guidelines:
  • Shelf Life: At normal temperatures (22 °C/72 °F), solder pastes usually have a storage life of between three and six months. Unrefrigerated: 25 °C (77 °F) / Refrigerated: 0°-12 °C (32 °F-55 °F).
  • Avoid Heat: The performance of solder paste may be impacted by exposure to temperatures above 30 °C (85 °F). Keep solder paste away from heat sources that are hotter than 32 °C (90 °F).
  • Orientation: When feasible, store solder pastes in syringes or cartridges vertically, tip down. Packages should occasionally be turned 180 degrees if they are horizontally stored.
  • FIFO System: Paste must be used before the date indicated on the product-specific TDS, which is the Date of Manufacturing (DOM) on the label. On a FIFO system with the date and time of removal from storage recorded, the oldest solder paste lots should be utilized first.
 

Critical Handling Rules

  • Do Not Use Cold: Cold usage of solder paste is not permitted. Before opening the paste package, filler material should be allowed to attain room temperature, which is 68°–77 °F (20°–25 °C). Normally, this takes between four and six hours. DO NOT HEAT THE PASTE FORCEFULLY (e.g., using a heat gun), as this causes condensation and flux separation.
  • Mixing: Паяльную пасту в банках следует слегка и тщательно перемешивать пластиковым инструментом в течение не менее одной минуты после того, как она достигнет комнатной температуры. Шприцы и картриджи для паяльной пасты перемешивать не нужно. Не рекомендуется использовать автоматическое оборудование для перемешивания паяльной пасты, так как это может повредить паяльную пасту.

PCB Solder Paste Printing: 3 Solder Paste Application Methods

This is the most critical step in Монтаж SMT, as over 70% of soldering defects originate from the printing process. There are three primary methods to apply solder paste onto the PCB.
solder paste printing in SMT line

Stencil Printing (Mass Production Standard)

Наиболее распространенной практикой является трафаретная печать, которая представляет собой специальную металлическую решетчатую структуру, обычно изготовленную из нержавеющей стали. Сначала производители создают Трафарет для печатной платы with holes or apertures of the same size and shape as the surface mount pads in the design. To ensure accuracy, FS Technology employs laser cutting technology to process the stencil and applies a coating material on the surface to smooth the apertures and facilitate even distribution of solder paste.
 
Затем трафарет помещается в SMT-устройство и выравнивается по отношению к расположенной под ним печатной плате. Паяльная паста равномерно наносится на трафарет, а лезвие скребка используется для соскабливания излишков пасты, позволяя ей капать на поверхность печатной платы через отверстия. Весь процесс обычно занимает от 15 до 45 секунд.
 
Post-Printing Inspection:
После завершения печати паяльной пасты, SPI (Solder Paste Inspection) testing is conducted to assess the uniformity and quality of the solder paste, ensuring each pad receives the correct coverage in terms of height, area, and volume. Finally, the stencil is cleaned after completing a batch of PCB solder paste printing to ensure that residue from the previous printing does not impact the distribution of solder paste on the next board.
Контроль паяльной пасты

Jet Printing (For Flexibility and Prototyping)

Хотя трафаретная печать выгодна для крупномасштабная сборка печатных платИзготовление трафарета занимает значительное время, а точный контроль количества паяльной пасты для каждого компонента является сложной задачей. Поэтому струйная печать становится все более популярной.
 
В струйной печати используется модифицированная формула для создания более жидкой паяльной пасты. Струйные принтеры, используя те же данные о дизайне печатной платы, что и при трафаретной печати, наносят точное количество паяльной пасты на каждую интерфейсную площадку на плате. В зависимости от материала припоя, необходимого для конкретного применения, принтер может легко переключаться и чередовать картриджи с паяльной пастой, из которых струей вытекают крошечные капельки паяльной пасты.
 
Advantage:
Технология струйной печати позволяет сборщикам печатных плат точно контролировать количество паяльной пасты для каждого интерфейса, обеспечивая им значительную гибкость. Это означает, что количество паяльной пасты для каждой точки пайки можно регулировать в зависимости от конкретных требований. прототипы and high-mix малосерийное производство.

Manual Application (For Rework and Hobbyists)

В проектах для ремонтников или хоббистов метод печати обычно не используется для нанесения паяльной пасты на печатные платы. Вместо этого существуют два распространенных ручных метода:
  • С помощью шприца точно нанесите паяльную пасту на контакты, а затем используйте паяльник, чтобы скрепить ее с контактами.
  • Поместите проволоку с припоем между двумя контактами компонента, а затем нагрейте ее с помощью паяльника.
 
Regardless of the method chosen, the ultimate goal is to establish a reliable connection between the PCB and the component. After manual soldering is completed, it is advisable to perform a quality check and conduct функциональные тесты to ensure the reliability of the connections.
Печать трафаретов для печатных плат

Common Solder Paste Defects and How to Prevent Them

Even with proper materials and equipment, soldering defects can occur. Recognizing the root causes and implementing preventive measures is key to maintaining high yield. Below are the most frequent defects encountered in SMT assembly, along with practical solutions.
ДефектVisual AppearancePrimary CausesPrevention & Corrective Actions
Solder BridgingSolder connects two adjacent pads or pins, creating a short circuit.Excessive solder paste volume; stencil apertures too large; low paste viscosity; improper squeegee pressure.Reduce stencil thickness or aperture size; adjust printing pressure; use higher viscosity paste; ensure proper alignment.
Tombstoning (Manhattan Effect)One end of a chip component lifts off the pad, standing upright.Uneven solder paste deposition on the two pads; different thermal mass on pads; rapid heating during reflow.Ensure uniform paste volume on both pads; optimize reflow profile (soak zone); use nitrogen atmosphere to balance wetting forces.
Solder Beading (Solder Balls)Small spherical solder balls scattered around the pad or under components.Paste slump (spreading) before reflow; excessive oxidation; fast ramp-up rate causing spattering.Use paste with higher viscosity and anti-slump properties; control reflow profile with a gradual ramp; ensure stencil aperture design prevents paste bleeding.
Insufficient Solder (Open Joint)Pad is not fully covered; component lead appears dry or lifted.Stencil clogged; insufficient paste volume; poor stencil release; worn squeegee.Clean stencil regularly (under-stencil wiping); increase aperture size or stencil thickness; check squeegee condition; perform SPI to catch volume variations.
Poor Wetting / Cold JointSolder does not spread properly; appears dull, grainy, or has a non-wetting surface.Inadequate flux activity; contaminated pads/components (oxidation); reflow temperature too low or time too short.Choose appropriate flux (ROL1/ROL2); bake PCBs prior to assembly to remove moisture; verify reflow profile with thermocouple.
Voids (in BGA/CSP)X-ray reveals gas bubbles within the solder ball.Outgassing from flux or PCB/component surface; insufficient preheat; too rapid cooling.Optimize reflow profile with longer soak; use low-voiding flux paste; ensure components and boards are dry.
FS Technology’s Quality Assurance:
We employ SPI inspection after printing and AOI (автоматизированная оптическая инспекция) plus Рентген after reflow to detect and eliminate these defects at every stage, ensuring your PCBA meets IPC Class 2 or Class 3 standards.

Заключение

Solder paste is the lifeblood of modern SMT assembly. From selecting the correct alloy and particle size (Type 3, 4, or 5) to rigorous storage protocols and precise printing processes, every step impacts the final quality of your PCBA.
 
На сайте Технология FS, we combine state-of-the-art equipment (including advanced SPI and jet printing systems) with strict process control to ensure your boards are assembled with the highest reliability. Whether you need high-volume production or быстрое прототипирование, our engineering team is ready to assist you in selecting the optimal solder paste for your specific application.
 

FAQs about Solder Paste

The difference lies in the powder particle size. Type 3 ranges from 25-45μm and is suitable for standard components and larger pitch ICs. Type 4 ranges from 20-38μm and is required for finer pitch components like 0201 and 0.4mm pitch BGAs, providing better print release and reduced solder balling.
Yes, but the temperature must be strictly controlled between 0°C and 12°C (32°F-55°F). Do not freeze the paste. Also, ensure the container is sealed tightly to prevent moisture absorption.
This is called “conditioning” . It allows the entire container of paste to reach room temperature evenly. If opened cold, moisture from the air will condense on the cold paste, leading to solder spatter and voids during reflow.
Typically, this is due to low humidity in the environment, prolonged exposure to air (draft), or a stencil temperature that is too high. It is recommended to keep the production environment at 22-28°C and 40-60% relative humidity, and to return unused paste to the jar if printing pauses for more than 30 minutes.
Use a solder paste formulated with low-voiding flux, optimize the reflow profile with a longer soak zone to allow outgassing, and ensure both the PCB and BGA components are properly baked to remove moisture prior to assembly.

Похожие блоги

Partner with us & Start your PBCA Project