Security Camera PCBA Design Guide: Day/Night Switching and Infrared LED Driver
Why Security Camera PCBA Design Matters for Day/Night Operation
IR-CUT Filter Switcher Driver Circuit Design
How IR-CUT Actuator Works in Day/Night Mode
- Day position: The IR-CUT filter moves close to the image sensor and blocks infrared light.
- Night position: The IR-CUT filter moves away from the sensor, allowing the sensor to detect the infrared light reflected from the objects.
H-Bridge Circuit for IR-CUT Actuator Polarity Reversal
- Select the IC that handles the actuator’s pulse current as well as prevents coil overheating.
- Use flyback protection for inductive voltage spikes and keep actuators switching traces far from RF circuits and sensors.
- Consider the delay between polarity reversals to reduce the shoot-through current.
IR-CUT H-Bridge Design Checklist
| Design Item | Recommended Check |
| Pulse current | Verify MOSFET/IC rating against actuator coil pulse current |
| Dead time | Add delay between polarity reversal to prevent shoot-through |
| Flyback protection | Use TVS, diodes, or snubber for inductive spikes |
| Trace routing | Keep switching traces away from RF, sensor, and antenna circuits |
| Voltage extremes | Test at minimum and maximum supply voltage |
| Cycle life | Validate IR-CUT switching over repeated day/night cycles |
| Thermal rise | Check actuator and driver heating after continuous cycling |
Infrared LED Array and Constant-Current Driver Design
Why Constant-Current Drive Is Necessary for IR LEDs
- Constant current regulation for each LED string
- Soft start to reduce the surge current at the time of activation.
- Overheating, ショートサーキット protection.
- PWM dimming control and low power at nighttime
IR LED Driver Design Checklist
| Design Item | Recommended Check |
| Current regulation | Maintain stable current per LED string |
| Soft start | Reduce inrush current during activation |
| Protection | Include OTP, OCP, short-circuit, and open-circuit protection |
| Dimming | Support PWM dimming for night-time power control |
| Thermal derating | Use NTC or temperature sensor for current derating |
| Standby power | Keep low power consumption when IR LEDs are off |
| Aging margin | Design current margin for LED forward-voltage drift |
Aluminum Substrate PCBA and Thermal Dissipation Design
- Aluminum substrate core PCBA for Infrared LEDs.
- Direct attachment of the LED board and the metal housing
- Separation of LEDs from temperature-sensitive circuits
- NTC thermistor or temperature sensor near the LED boards
- Proper spacing between the LEDs to avoid concentrated heat zones
Video Output and Network Signal Integrity
Wi-Fi Antenna Placement and RF Noise Control
Ethernet and PoE Interface Design for Security Cameras
IP66 Waterproof Sealing and Lens Defogger Heater Control
IP66 Enclosure Requirements for Security Cameras
Lens Defogger Heater Circuit
Design Verification and Reliability Testing
| Test Area | Test Condition | Pass Criteria |
| Day/Night switching | Different ambient light levels | No delay, no blur, correct color/mono mode |
| IR-CUT actuator | Pulse current, high/low temp, voltage extremes | Full movement without sticking |
| IR-CUT cycle life | Repeated switching cycles | Meets target cycle count |
| IR LED current | Full load, temperature variation | Stable current and brightness |
| Thermal derating | Enclosed housing, max ambient | Junction temperature below derating limit |
| Wi-Fi performance | Antenna placement comparison | Stable video stream and range |
| Ethernet / PoE | Throughput and surge test | No packet loss or interface damage |
| Condensation | Temperature/humidity cycling | No fogging or moisture damage |
| IP66 | Dust and water jet | No ingress into enclosure |
Common Failure Modes in Security Camera PCBA Design
| Failure Mode | Possible Root Cause | Design Countermeasure |
| IR-CUT filter partially moves | Weak pulse current, H-bridge timing error, mechanical friction | Verify pulse current, add dead time, use flyback protection |
| Night image is weak or blurry | IR LED current unstable, insufficient illumination | Use constant-current driver and validate PWM dimming |
| Image color is wrong in daytime | IR-CUT filter does not block IR light | Test actuator position and day-mode pulse |
| IR LED overheating | Poor thermal path, excessive current, no derating | Use aluminum substrate, NTC, and thermal simulation |
| Wi-Fi video drops | Antenna near high-current IR LED or switching converter | Improve antenna clearance, grounding, and decoupling |
| PoE interface damage | Surge, ESD, or poor isolation | Add TVS/ESD protection near RJ45 and follow PoE standards |
| Lens fogging | Defogger control logic or NTC threshold error | Validate heater PWM, NTC placement, and firmware logic |
| Condensation inside camera | Poor IP66 sealing or trapped water | Use gaskets, sealed connectors, conformal coating, and drainage |
Security Camera PCBA Design Checklist
- Confirm day/night switching logic and ambient light thresholds.
- Validate IR-CUT actuator pulse current, polarity reversal, and cycle life.
- Use an H-bridge with shoot-through prevention and inductive flyback protection.
- Design a constant-current IR LED driver with soft start and PWM dimming.
- Add overheating, short-circuit, and open-circuit protection.
- Use aluminum substrate PCBA for high-power IR LED thermal dissipation.
- Place NTC thermistor or temperature sensor near the IR LED board.
- Keep Wi-Fi antenna away from IR LED traces, actuator, and switching converters.
- Protect Ethernet and PoE interfaces with surge and ESD devices.
- Follow IP66 sealing, conformal coating, and drainage design requirements.
- Test the complete camera under thermal, condensation, and water jet conditions.
- Review component derating and aging margins before production.
グローバル展開を加速する
信頼性の高いPCBAを使用
One-stop solution: PCB fabrication, sourcing, SMT assembly, testing & global logistics.
迅速な対応、厳格な品質管理。.
結論
FAQs about Security Camera PCBA Design
What is an IR-CUT filter in a security camera?
Why does an IR-CUT actuator need an H-bridge?
Why is constant-current drive better for IR LEDs?
How to improve thermal dissipation in security camera PCBA?
What is the difference between IP66 and IP67?
How to protect PoE interface from surge?
Where should the Wi-Fi antenna be placed in a security camera?
FSテクノロジーと提携して、プロフェッショナルなPCBAサービスを手に入れましょう。
関連ブログ
Table of Contents Medical PCBA Cost in 2026: What Really Drives the 2.5–4× Premium Over Commercial Boards Medical PCBA costs do not only depend on
Table of Contents PCBA Functional Testing (FCT): A Complete Guide to Ensuring Board Reliability Published on May 9, 2023 · Updated on November 6, 2026
Table of Contents IPC Class 2 vs Class 3: Acceptance Criteria, Cost Impact, and How to Choose IPC Class 2 and Class 3 are the
Table of Contents Ventilator PCB Assembly: ISO 13485, IPC Class 3 & FDA QMSR-Ready Manufacturing Published on June 24, 2022 · Updated on October 30,
Table of Contents Ventilator PCB Assembly: ISO 13485, IPC Class 3 & FDA QMSR-Ready Manufacturing How is air delivered steadily with the help of ventilators,
Table of Contents Design Rule Checking in PCB Design: From Altium DRC to SMT Assembly Published on September 10, 2024 · Updated on October 22,