Table des matières

Solder Paste in PCB Assembly: Selection, Printing, Defects & Expert Tips

This article was originally published in Jan 2023 and last updated on July 19, 2026.

A crucial component in electronic devices is the PCBA board, consisting of two main parts: PCB et Composants. The PCB supports and connects the components, which, in turn, provide the actual functionality. Initially, these two parts are separate, but through the assembly and soldering process, they are eventually combined into a unified whole.
 
In this assembly process, the use of certain key materials is necessary, and one of these is pâte à souder. This article will provide a detailed overview of the role of solder paste and a guide on how to correctly use solder paste in the Processus d'assemblage des PCB.
Solder Paste in SMT Assembly

What is Solder Paste and Why Use it?

One of the most reliable methods to connect two metals without melting them is soldering, and solder paste is essential for achieving this. Pâte à souder is a special metal alloy composed of metal solder particles and a unique combination of flux. During the soldering process, the distinctive properties of solder paste allow it to melt and form a permanent bond, thus establishing a reliable connection between metals.
 
To ensure good performance during the soldering process, solder paste must meet several important standards:
  1. Low Melting Point: Given the heat sensitivity of the components, it should have a low melting point. In case the melting point is too high, there could be a possibility of the components being subjected to the maximum possible heat before completely melting.
  2. High Conductivity: It serves the purpose of not only making physical contact but also providing the electrical connection to enable the free flow of electrical current through the components.
  3. Compliant to RoHS Directive: The use of solder paste should be done such that it complies with the strict guidelines set by the Directive RoHS.
 
In the past, approximately 40% of solder pastes in electronic manufacturing consisted of a combination of lead and tin. However, due to the environmental hazards associated with lead, and with advancements in technology and increased environmental awareness, the fabrication électronique industry has gradually transitioned to lead-free processes. Consequently, lead-free solder paste has become the mainstream choice, reflecting a positive response to environmental concerns and industry focus on health and sustainability.
Impression de pâte à braser lors de l'assemblage de circuits imprimés

Solder Paste Type: Particle Size, Flux & Alloy

L'utilisation d'une pâte à braser de haute qualité et du bon type est une étape cruciale pour garantir la qualité des cartes PCBA. Pour les projets d'assemblage, FS Technology propose différentes qualités et différents types de pâtes à souder pour répondre à différentes exigences. Vous pouvez choisir en fonction des matériaux prévus pour le brasage et des besoins, ou sélectionner en fonction de la taille des billes de soudure dans la pâte à braser.

By Particle Size (Powder Type)

Pour répondre aux exigences des différents projets, les pâtes à braser sont généralement divisées en différentes qualités et catégories. Ces catégories ne sont pas uniquement basées sur la taille exacte des billes de soudure, mais sont évaluées sur la base d'environ 80% des billes de soudure se situant dans une fourchette de taille spécifique. Voici les différents grades et les tailles de billes de soudure correspondantes.

Qualité de la pâte à braser

Taille de la particule

Type 1

75mm à 150mm

Type 2

45mm à 75mm

Type 3

25mm à 45mm

Type 4

20mm à 38mm

Type 5

10mm à 25mm

Type 6

5mm à 15mm

Type 7

2mm à 11mm

Type 8

2mm à 8mm

Conseil de pro :
For standard SMT assembly with 0603 components and 0.4mm pitch ICs, Type 4 solder paste (20-38μm) is the most versatile and widely recommended choice. For ultra-fine pitch applications like 01005 components, Type 5 or finer is required.

By Flux Type

Outre la taille des particules, le choix de la pâte à braser appropriée en fonction du type de flux est également une option viable. Les différents types de Flux de PCB peut mieux correspondre à des formulations spécifiques de pâte à braser afin d'obtenir de meilleurs résultats de brasage ou de répondre à des exigences spécifiques en matière de processus. Cependant, tous les environnements ne permettent pas l'utilisation de ce type de flux, et il faut s'assurer que l'environnement est suffisamment propre.
  • Pâte de flux soluble dans l'eau : Composé de composants organiques et d'une base d'éthylène glycol. Les résidus de flux solubles dans l'eau peuvent être facilement éliminés à l'aide de produits de nettoyage disponibles sur le marché.
  • Pâte à braser sans nettoyage : Ce type de pâte à braser est généralement utilisé dans la fabrication de flux sans nettoyage. Elle contient relativement peu de résidus solides et de résine. Le principal avantage de l'utilisation d'un flux sans nettoyage est l'économie potentielle sur les produits de nettoyage.
  • Pâte à braser à base de colophane : Les pâtes à souder de ce type sont fabriquées à partir de colophane et peuvent être nettoyées à l'aide de solvants après la soudure.

By Alloy Composition

Whereas the original passage is concerned about the size of particles, the choice of alloy is just as important. The selection of alloy will determine the melting temperature, mechanical strength, and reliability of the solder joint.
  • SAC305 (Sn96.5/Ag3.0/Cu0.5): Industry standard for lead-free soldering applications. Provides the optimal combination of cost, thermal fatigue resistance, and wetting properties, thus suitable for all general-purpose applications such as automobiles and industrial electronics.
  • Low Temperature Alloys (for example, Sn-Bi): Used for components that require low temperature or when secondary reflow is necessary, with primary solder joints remaining intact.
  • High Reliability Alloys: Sometimes containing additional elements such as Nickel or Bismuth to improve drop shock and creep resistance, critical for aérospatiale et médical devices.

How to Select the Right Solder Paste for Your PCBA Project?

The selection of an appropriate type of solder paste is not universal. In order to have a high yield rate and reliability, you need to consider your project based on the following criteria. Please use the decision guide together with the technical information above.
Project FactorRecommended Solder Paste CharacteristicsRationale
Component Density & MiniaturizationFor high-density boards with 0201/01005 components and <0.4mm pitch BGAs, choose Type 4 or Type 5 powder with fine particle size.Finer powders ensure better print release and prevent clogging in narrow apertures, reducing the risk of insufficient solder.
Product Reliability RequirementsFor automotive, medical, or aerospace applications, opt for ROL0 (low-activity) no-clean flux combined with SAC305 or high-reliability alloys.Low-activity flux leaves minimal ionic residues, preventing electrochemical migration. High-reliability alloys offer superior thermal cycling and shock resistance.
Production Volume & MixFor high-mix, low-volume or prototype runs, Jet Printing with a fluid solder paste offers flexibility. For mass production, stencil printing with Type 4 paste is cost-effective.Jet printing eliminates stencil costs and allows quick changeovers. Stencil printing provides high throughput for repetitive jobs.
Conformité réglementaireIf your products are exported to EU or North America, ensure the solder paste is RoHS-compliant (lead-free). For medical implants, also consider biocompatible alloys.Non-compliance can lead to legal barriers and market rejection.
Process Window & EquipmentMatch the paste’s viscosity to your printing equipment (squeegee speed, pressure). Also, ensure your reflow oven can handle the recommended temperature profile.Incompatible viscosity causes smearing or insufficient release. Wrong profile leads to cold joints or component damage.
Recommendation from FS Technology:
In case of general electronics applications such as consumer and industrial controls, which account to about 80%, we advise the use of SAC305 Alloy in combination with Type 4 and No-clean ROL1 Flux, as it offers the most reliable solution at an affordable price. For specific needs, our engineering team is available for personalized consultation.

Best Practices for Solder Paste Storage and Handling

Solder Paste Storage in FS TECH
En fonction de la température et de l'humidité du Usine de PCBALes pâtes à souder prêtes à l'emploi doivent être conservées dans un emballage spécialement conçu à cet effet, qui maintient la température du produit entre 0° et 30 °C pendant au moins 48 heures.
 
La pâte à braser doit être livrée de nuit ou par transport réfrigéré. En été, transportez-la de nuit autant que possible pour réduire le temps et éviter les températures élevées. L'emballage de la pâte peut inclure des packs de froid qui arrivent fondus. Si le temps de transport de 48 heures n'est pas dépassé, cela est typique et n'est pas un signe de dommage ou de mauvaise manipulation. À l'arrivée, la pâte à braser doit être déplacée immédiatement vers un stockage contrôlé. L'utilisation de la réfrigération est conseillée mais pas toujours nécessaire.
 
Detailed Storage Guidelines:
  • Shelf Life: At normal temperatures (22 °C/72 °F), solder pastes usually have a storage life of between three and six months. Unrefrigerated: 25 °C (77 °F) / Refrigerated: 0°-12 °C (32 °F-55 °F).
  • Avoid Heat: The performance of solder paste may be impacted by exposure to temperatures above 30 °C (85 °F). Keep solder paste away from heat sources that are hotter than 32 °C (90 °F).
  • Orientation: When feasible, store solder pastes in syringes or cartridges vertically, tip down. Packages should occasionally be turned 180 degrees if they are horizontally stored.
  • FIFO System: Paste must be used before the date indicated on the product-specific TDS, which is the Date of Manufacturing (DOM) on the label. On a FIFO system with the date and time of removal from storage recorded, the oldest solder paste lots should be utilized first.
 

Critical Handling Rules

  • Do Not Use Cold: Cold usage of solder paste is not permitted. Before opening the paste package, filler material should be allowed to attain room temperature, which is 68°–77 °F (20°–25 °C). Normally, this takes between four and six hours. DO NOT HEAT THE PASTE FORCEFULLY (e.g., using a heat gun), as this causes condensation and flux separation.
  • Mixing: La pâte à souder en pot doit être légèrement et soigneusement mélangée avec un outil en plastique pendant au moins une minute après avoir atteint la température ambiante. Les seringues et les cartouches de pâte à braser n'ont pas besoin d'être mélangées. Il n'est pas conseillé d'utiliser un équipement automatisé pour mélanger la pâte à braser, car cela pourrait endommager la pâte à braser.

PCB Solder Paste Printing: 3 Solder Paste Application Methods

This is the most critical step in Montage SMT, as over 70% of soldering defects originate from the printing process. There are three primary methods to apply solder paste onto the PCB.
solder paste printing in SMT line

Stencil Printing (Mass Production Standard)

La pratique la plus courante est l'impression au pochoir, qui est une structure métallique spéciale en forme de grille, généralement en acier inoxydable. Les fabricants créent d'abord un Pochoir pour circuits imprimés with holes or apertures of the same size and shape as the surface mount pads in the design. To ensure accuracy, FS Technology employs laser cutting technology to process the stencil and applies a coating material on the surface to smooth the apertures and facilitate even distribution of solder paste.
 
Le pochoir est ensuite placé dans un dispositif SMT et aligné avec le circuit imprimé situé en dessous. La pâte à braser est appliquée uniformément sur le pochoir et une raclette est utilisée pour racler l'excès de pâte, ce qui lui permet de tomber sur la surface du circuit imprimé à travers les ouvertures. L'ensemble du processus prend généralement entre 15 et 45 secondes.
 
Post-Printing Inspection:
Une fois l'impression de la pâte à braser terminée, SPI (Inspection de la pâte à braser) testing is conducted to assess the uniformity and quality of the solder paste, ensuring each pad receives the correct coverage in terms of height, area, and volume. Finally, the stencil is cleaned after completing a batch of PCB solder paste printing to ensure that residue from the previous printing does not impact the distribution of solder paste on the next board.
Inspection de la pâte à braser

Jet Printing (For Flexibility and Prototyping)

Si l'impression au pochoir est avantageuse pour assemblage de PCB à grande échelleLa construction du pochoir prend un temps considérable et le contrôle précis de la quantité de pâte à braser pour chaque composant est difficile. C'est pourquoi l'impression par jet d'eau devient de plus en plus populaire.
 
L'impression à jet d'encre utilise une formule modifiée pour créer une pâte à souder plus liquide. Les imprimantes à jet d'encre, utilisant les mêmes données de conception de circuits imprimés que l'impression au pochoir, appliquent une quantité précise de pâte à braser sur chaque plot d'interface de la carte. En fonction du matériau de soudure requis pour l'application, l'imprimante peut facilement changer et alterner entre les cartouches de pâte à braser, à partir desquelles de minuscules gouttelettes de pâte à braser sont projetées.
 
Advantage:
La technologie Jet Printing permet aux assembleurs de circuits imprimés de contrôler avec précision la quantité de pâte à braser pour chaque interface, ce qui leur confère une grande flexibilité. Cela signifie que les quantités de pâte à braser pour chaque point de soudure peuvent être ajustées en fonction d'exigences spécifiques. prototypes and high-mix production en faible volume.

Manual Application (For Rework and Hobbyists)

Dans les projets de réparation ou de bricolage, la méthode d'impression n'est généralement pas utilisée pour appliquer la pâte à braser sur les circuits imprimés. Il existe plutôt deux méthodes manuelles courantes :
  • À l'aide d'une seringue, appliquez précisément la pâte à souder sur les broches, puis utilisez un fer à souder pour la faire adhérer aux broches.
  • Placez le fil de soudure entre les deux broches du composant, puis utilisez un fer à souder pour le chauffer.
 
Regardless of the method chosen, the ultimate goal is to establish a reliable connection between the PCB and the component. After manual soldering is completed, it is advisable to perform a quality check and conduct tests fonctionnels to ensure the reliability of the connections.
Impression de pochoirs pour circuits imprimés

Common Solder Paste Defects and How to Prevent Them

Even with proper materials and equipment, soldering defects can occur. Recognizing the root causes and implementing preventive measures is key to maintaining high yield. Below are the most frequent defects encountered in SMT assembly, along with practical solutions.
DéfautVisual AppearancePrimary CausesPrevention & Corrective Actions
Solder BridgingSolder connects two adjacent pads or pins, creating a short circuit.Excessive solder paste volume; stencil apertures too large; low paste viscosity; improper squeegee pressure.Reduce stencil thickness or aperture size; adjust printing pressure; use higher viscosity paste; ensure proper alignment.
Tombstoning (Manhattan Effect)One end of a chip component lifts off the pad, standing upright.Uneven solder paste deposition on the two pads; different thermal mass on pads; rapid heating during reflow.Ensure uniform paste volume on both pads; optimize reflow profile (soak zone); use nitrogen atmosphere to balance wetting forces.
Solder Beading (Solder Balls)Small spherical solder balls scattered around the pad or under components.Paste slump (spreading) before reflow; excessive oxidation; fast ramp-up rate causing spattering.Use paste with higher viscosity and anti-slump properties; control reflow profile with a gradual ramp; ensure stencil aperture design prevents paste bleeding.
Insufficient Solder (Open Joint)Pad is not fully covered; component lead appears dry or lifted.Stencil clogged; insufficient paste volume; poor stencil release; worn squeegee.Clean stencil regularly (under-stencil wiping); increase aperture size or stencil thickness; check squeegee condition; perform SPI to catch volume variations.
Poor Wetting / Cold JointSolder does not spread properly; appears dull, grainy, or has a non-wetting surface.Inadequate flux activity; contaminated pads/components (oxidation); reflow temperature too low or time too short.Choose appropriate flux (ROL1/ROL2); bake PCBs prior to assembly to remove moisture; verify reflow profile with thermocouple.
Voids (in BGA/CSP)X-ray reveals gas bubbles within the solder ball.Outgassing from flux or PCB/component surface; insufficient preheat; too rapid cooling.Optimize reflow profile with longer soak; use low-voiding flux paste; ensure components and boards are dry.
FS Technology’s Quality Assurance:
We employ SPI inspection after printing and AOI (Inspection optique automatisée) plus Rayon X after reflow to detect and eliminate these defects at every stage, ensuring your PCBA meets IPC Class 2 or Class 3 standards.

Conclusion

Solder paste is the lifeblood of modern SMT assembly. From selecting the correct alloy and particle size (Type 3, 4, or 5) to rigorous storage protocols and precise printing processes, every step impacts the final quality of your PCBA.
 
Au Technologie FS, we combine state-of-the-art equipment (including advanced SPI and jet printing systems) with strict process control to ensure your boards are assembled with the highest reliability. Whether you need high-volume production or prototypage rapide, our engineering team is ready to assist you in selecting the optimal solder paste for your specific application.
 

FAQs about Solder Paste

The difference lies in the powder particle size. Type 3 ranges from 25-45μm and is suitable for standard components and larger pitch ICs. Type 4 ranges from 20-38μm and is required for finer pitch components like 0201 and 0.4mm pitch BGAs, providing better print release and reduced solder balling.
Yes, but the temperature must be strictly controlled between 0°C and 12°C (32°F-55°F). Do not freeze the paste. Also, ensure the container is sealed tightly to prevent moisture absorption.
This is called “conditioning” . It allows the entire container of paste to reach room temperature evenly. If opened cold, moisture from the air will condense on the cold paste, leading to solder spatter and voids during reflow.
Typically, this is due to low humidity in the environment, prolonged exposure to air (draft), or a stencil temperature that is too high. It is recommended to keep the production environment at 22-28°C and 40-60% relative humidity, and to return unused paste to the jar if printing pauses for more than 30 minutes.
Use a solder paste formulated with low-voiding flux, optimize the reflow profile with a longer soak zone to allow outgassing, and ensure both the PCB and BGA components are properly baked to remove moisture prior to assembly.

Blogs associés

Partner with us & Start your PBCA Project