Table of Contents

Design Rule Checking in PCB Design: From Altium DRC to SMT Assembly

Published on September 10, 2024 · Updated on October 22, 2026

Design Rule Check (DRC) is the final automated step in the PCB layout process before going into manufacturing – and for most design teams, the green tick that pops up after completing the process is akin to crossing the finish line. It’s not. This article will explore what Design Rule Checking does, what type of rules it checks for, and how to do DRC in PCB design and solve any issues found in Altium Designer. It will also discuss what DRC does not catch: the assembly issues that fail at every geometric rule but emerge in the form of solder bridges, open BGA connections, and even reversed components during the SMT assembly process. For engineers from an OEM organization or project managers preparing their designs for overseas manufacturing, the sections about DRC versus DFA/DFM and assembly issues are for you.
Design Rule Checking in PCB Design - From Altium DRC to SMT Assembly

What is Design Rule Checking (DRC)​

Design Rule Checking (DRC) is a process used in electronic design automation (EDA) to verify that a PCB design adheres to a set of predefined rules or constraints. These rules ensure that the design is manufacturable, reliable, and meets the necessary performance standards.
 
DRC work by comparing the layout of the PCB design against a set of predefined rules established by the designer or manufacturer. These rules are based on industry standards, manufacturing capabilities, and the specific requirements of the project.
 
The primary goal of DRC check is to detect errors early in the design process that could lead to manufacturing defects or functional failures in the final product. By adhering to DRC rules, designers can minimize risks, reduce the need for rework, and ensure that the fabricated PCB is both reliable and manufacturable.
 
But passing DRC is only the first gate — the question a PCBA partner ultimately answers is whether the board can be assembled at yield, not just whether it matches a rule deck.

Why Design Rule Checking (DRC) is Essential in PCB Design

Design Rule Checking (DRC) is a fundamental aspect of PCB design that ensures the board is both manufacturable and reliable. By adhering to a set of predefined rules, DRC helps identify potential issues early in the design process, preventing costly errors and ensuring that the final product meets the necessary standards. Here’s why DRC is essential in PCB design:
 

Preventing Manufacturing Defects

During PCB manufacturing, processes such as photolithography, etching, drilling, and plating must adhere to specific parameters to avoid defects. Without strict adherence to design guidelines, the PCB can experience open circuits, short circuits, or complete failure. DRC is essential because it catches these potential issues before production begins, ensuring the design stays within the manufacturing process’s capabilities and prevents defects that could compromise the board’s functionality.
 

Ensuring Electrical Integrity

Electrical integrity is crucial for a PCB’s performance. DRC ensures that design elements like trace widths, via placement, and spacing meet the necessary electrical design rules. This is essential to prevent issues such as high resistance, crosstalk, and signal interference. Properly configured DRC rules help maintain the PCB’s electrical integrity, ensuring that it performs reliably and efficiently in its intended application.
 

Ensuring Compliance with Industry Standards

Compliance with industry standards is critical, especially in sectors like aviation, automotive, and medical devices, where safety and reliability are paramount. DRC is essential in verifying that the PCB design adheres to these strict standards, providing designers with confidence that their boards will meet regulatory requirements. This compliance not only ensures a safe and reliable final product but also streamlines the certification process, which is often required in these industries.
 

Accelerating Time-to-Market

In a fast-paced industry, getting products to market quickly is crucial. Errors discovered during or after manufacturing can cause significant delays. DRC is essential because it identifies potential issues early, reducing the likelihood of time-consuming redesigns and re-manufacturing. By catching errors in the design phase, DRC enables a faster transition from development to production, helping companies bring their products to market more efficiently.
 

Enhancing Cost Efficiency

Fixing PCB design errors after manufacturing can be expensive, especially if faulty boards need reworking or scrapping. DRC is essential in minimizing these assembly costs by identifying errors during the design phase, before any physical boards are produced. This proactive approach not only reduces labor and material costs but also leads to more financially sustainable project outcomes. By ensuring the design is manufacturable from the start, DRC contributes to a more cost-effective PCB manufacturing process.

Where DRC Stops and DFM / DFA / DFT Begin

DRC design rule check is necessary but not sufficient. It checks geometry against the rules you loaded into the EDA tool; it does not check whether those rules match the assembly line that will build the board. The table below draws the boundary.
Check TypeCore QuestionCovered by DRC?
DRCDoes the design comply with the configured geometric and connectivity rules?Yes
DFM (including DFF)Can the bare board be reliably manufactured by a specific fab‘s etching, drilling, copper plating, and solder mask processes?Partially — only when the rules are bound to that fab’s process window
DFACan components be reliably placed and soldered on a specific SMT line?No
DFTCan the assembled board be effectively tested by ICT / flying probe?No
DRC is a hard pass/fail connectivity and spacing check; DFM is more concerned with features in the PCB topology that have the potential to cause manufacturing problems. DFA errors, by contrast, do not surface until the board reaches the SMT line — which is the root cause of DRC-clean designs failing at PCB assembly.

Key Design Rule Check (DRC) rules

  1. Clearance Rules

  • Minimum Spacing: This is one of the most critical rules, ensuring that there is adequate space between different conductive elements such as traces, pads, and vias. Proper clearance prevents electrical shorts, which could lead to circuit malfunction or even catastrophic failure.
  1. Trace Width Rules

  • Trace Width: Ensuring that trace widths meet the design specifications is vital for carrying the required current without overheating. This rule is crucial for maintaining the reliability and safety of the PCB, especially in high-current applications.
  1. Via Rules

  1. Annular Ring Rules

  • Minimum Annular Ring: A sufficient annular ring is essential for the mechanical strength of vias. If the ring is too small, it may cause pads to detach or lead to poor solder joint quality, which compromises the board’s reliability.
  1. Solder Mask Rules

  • Solder Mask Expansion: This rule is critical to preventing solder bridges during assembly. Ensuring that the solder mask is correctly expanded around pads and traces helps to avoid short circuits and manufacturing defects.
  1. Plane Connection Rules

  • Thermal Relief: Applying proper thermal relief to pads connected to large copper planes is crucial for both manufacturability and reliability. Without thermal relief, pads may become difficult to solder, leading to poor connections and potential field failures.
  1. Signal Integrity Rules

  • Crosstalk and Impedance Control: In high-speed designs, controlling crosstalk and ensuring that traces maintain the correct impedance are critical for signal integrity. These rules prevent data corruption and ensure that signals are transmitted accurately across the PCB.
  1. Component Placement Rules

  • Placement Within Board Edges and Height Constraints: Proper component placement ensures that components are secure and that the PCB can be housed properly within its intended enclosure. Violating these rules can lead to mechanical stress or damage during assembly or use.

What DRC Does Not Catch and Why It Matters at Assembly

All eight of these rule categories are crucial; however, they all have one common problem: they function using the rule values which were imported to the EDA tool. In case the rule is either set too loosely, not included into the checking process, or just does not exist for the given failure mode, DRC check would say that the design is clean even though it contains the flaw.
 
Scenario 1: Bridging of the solder dam between fine-pitch pads. 0.5 mm pitch QFP with 4 mils wide solder mask dam passes DRC when rule minimum is 3 mils. However, fabrication facility that has ±2 mil registration tolerance has about 50% probability of having the dam bridged during the imaging process. If DFM checks are run against the capabilities of the fabrication facility, the check will catch it and recommend 5 mils instead of 4 mils. The DRC verified the rule but it did not verify the process window for the rule.
 
Scenario 2: Via in Pad with no resin filling. DRC finds a valid via within a valid pad and does not report any violation of rule. During reflow, solder travels through the via and starves the ball joint in BGA, resulting in an open that passes AOI but fails functional test. There is no geometric rule violation here because the problem is in process physics.
 
Scenario 3: Silkscreen polarity marking that is not consistent with the footprint. Generally speaking, EDA tools do not have any strict rules about silkscreen, thus it is possible to put pin 1 marking upside down or just not place it for the BGA package; this will not cause failure in the DRC process. The operator and AOI system on the SMT line work according to the silkscreen marking and will put the component upside down during the functional testing. DRC checks connectivity and clearance.
 
The bottom line: DRC ensures that your design adheres to the rules which you entered into your system. However, DRC does not ensure that these rules take into account the assembly process of building the board. Layout review conducted by the real assembly partner would discover 30 to 50 percent more problems than any generic rule set review.

How To use Design Rule Checking (DRC) in Altium Designer

Step 1: Access the Design Rules Editor

  1. Open Your PCB Project: Launch Altium Designer and open your PCB project.
  2. Navigate to the PCB Editor: Make sure you are in the PCB Editor workspace.
  3. Open the Design Rules Editor: Go to the top menu and select Design > Rules. This opens the PCB Rules and Constraints Editor, where you can configure and manage all the design rules.
Step 1 Access the Design Rules Editor

Step 2: Configure the Design Rules

  1. Select a Rule Category: In the left panel, choose a category that corresponds to the type of rules you want to configure (e.g., Electrical, Routing, Manufacturing).
  2. Add or Edit Rules:
    • Add New Rule: To create a new rule, click the New Rule button at the bottom of the window.
    • Double-Click to Edit: You can double-click an existing rule from the middle panel to modify its settings, or select the rule in the left panel to bring up the relevant parameters for editing.
  3. Set Rule Parameters:
    • Name: Give the rule a meaningful name that reflects its purpose.
    • Scope: Define the scope of the rule, specifying whether it applies to all nets, specific nets, layers, or components.
    • Attributes: Set the specific attributes of the rule, such as trace width, clearance, or via sizes. These parameters should align with the manufacturing capabilities and the requirements of your design.
  4. Prioritize Rules: If there are overlapping rules, click on the Priorities button to set the order of precedence for rule enforcement.
DRC Step 2 Configure the Design Rules

Step 3: Run the Design Rule Check (DRC)

  1. Initiate DRC:
    • Go to Tools > Design Rule Check from the top menu.
    • This opens the DRC dialog, where you can configure the check.
  2. Configure DRC Settings:
    • Select Rules to Check: Choose which rules to apply during the DRC. You can select all rules or specific categories, depending on what you want to validate.
    • Output Options: Decide how you want to receive the results—whether as on-screen markers, in a detailed report, or both.
  3. Run the DRC:
Step 3 Run the Design Rule Check 1
Step 3 Run the Design Rule Check2

Step 4: Review and Resolve DRC Violations

  1. Examine the Results:

    • If there are any rule violations, they will be displayed in the Messages window, as shown on the right side of your Altium Designer workspace.
    • Each violation is typically listed with details such as the type of violation, the affected net or component, and its location on the PCB.
    • You can also generate a detailed report that lists all violations, with descriptions and locations.
  2. Directly Locate Violations:

    • Click on the Violations: In the Messages window, click on any specific violation. Altium Designer will automatically zoom in and highlight the exact area in the PCB layout where the issue is located. This allows for quick identification and resolution of problems without manually searching through the design.
  3. Resolve Violations:

    • For each violation, examine the highlighted area in the PCB layout.
    • Modify the layout to resolve the issue. This might involve adjusting trace widths, spacing, or component placements.
    • After making changes, re-run the DRC to ensure that the violation is resolved.
DRC Step 4 Review and Resolve DRC Violations
violations report

Step 5: Finalize the Design

  1. Re-Run DRC: After resolving all violations, run the DRC again to confirm that there are no remaining issues.
  2. Save and Document: Once your design passes the DRC with no violations, save your project. It’s also a good practice to document the final rules used and any exceptions for future reference or for your manufacturing partner.
  3. Prepare for Fabrication: With all DRC issues resolved, your PCB design is now ready for the next steps in the fabrication process.

How To import Design Rule Check (DRC) settings into Altium Designer?

Consider using the import function for design rules in Altium Designer when you want to ensure consistent standards across projects, easily align with specific manufacturing requirements, or streamline the design process, particularly at the start of a new project or when working in a team. This can help reduce errors and make collaboration smoother.

Step 1: Open the Design Rules Editor

  1. Open Your PCB Project: Start Altium Designer and load your PCB project.
  2. Access the Design Rules Editor: Go to Design > Rules in the top menu to open the PCB Rules and Constraints Editor.
Step 1 Access the Design Rules Editor

Step 2: Importing or Exporting Rules

  1. Right-Click on the Design Rules Folder: In the PCB Rules and Constraints Editor, right-click on the Design Rules folder at the top of the left panel.

  2. Choose Import or Export:

    • Import Rules: Select Import Rules to bring in design rules from an external file.
    • Export Rules: Select Export Rules to save the current design rules to an external file.
  3. Select Rules: In the Choose Design Rule Type panel that appears, select the specific rules you want to import or export. You can also press Ctrl + A to select all rules.

  4. Complete the Action:

    • For Importing: After selecting Import Rules, choose the .rul file from your system and click OK.
    • For Exporting: After selecting Export Rules, specify the location and file name to save the .rul file and click OK.
DRC Import Rules or Export Rules
Choose Design Rule Type

Conclusion

Design Rule Checking (DRC) is vital for ensuring that your PCB designs are error-free, reliable, and ready for manufacturing. By integrating DRC into every stage of your design process, you can catch issues early, reducing costs and avoiding delays.
 
If you need support with DRC check or any other aspect of PCB design, FS PCBA is here to help. We offer expert guidance and services to ensure your designs meet the highest standards, streamlining the path from concept to production. Let us assist you in bringing your projects to life with confidence and efficiency.

FAQs about Design Rule Check

Does passing DRC mean my PCB is ready for assembly?
No. DRC verifies geometry against the rules loaded in your EDA tool, but it does not confirm those rules match the assembly line‘s process window or catch failures like solder bridging, via-in-pad wicking, or silkscreen polarity errors. A DRC-clean design can still fail at SMT.
DRC checks geometry against configured rules. DFM checks whether the bare board can be built reliably at a specific fab. DFA checks whether components can be placed and soldered reliably on a specific SMT line. DRC is largely a hard pass/fail check; DFM and DFA address process issues that may not violate a geometric rule.
Yes. Common examples include solder bridging on fine-pitch pads where the mask dam is legal per the EDA rule but narrower than the fab’s registration tolerance can reliably produce, via-in-pad without resin fill that opens at functional test, and silkscreen polarity markers that contradict the footprint.
Ask for a review against their actual line capabilities: minimum solder-mask dam width at their registration tolerance, via-in-pad fill specification, component clearance for pick-and-place, panelization and fiducial requirements, and silkscreen polarity consistency. A partner that only runs DRC and quotes is not performing an assembly-side review.
A pre-release review against the builder‘s process window typically costs 2–4 hours of engineering time. A re-spin caused by a missed assembly-side issue costs $5,000–$25,000 and 4–8 weeks at the low end; industry averages for a single PCB re-spin run higher, around $46,000. Catching the gap earlier is cheaper by roughly an order of magnitude per stage.

Partner with FS Technology, Get Professional PCBA Service

Related Blogs