Inhaltsverzeichnis
Why Your RTC Battery Fails After 6 Months – And How to Fix It in Hardware
What is a Real-Time Clock (RTC)?
Electrical Characteristics Requirements for RTC Backup Batteries
Stromverbrauch
| RTC IC | Typical Backup Current |
| DS3231 | 0.84 µA (typ) at 3V |
| PCF8523 | 0.22 µA (typ) at 3V |
| MCP7940N | 1.1 µA (typ) at 3V |
| RV-3028-C7 | 0.045 µA (typ) at 3V |
| ABX00006 (Arduino) | 0.22 µA (typ) at 3V |
| RX-8025T | 0.75 µA (typ) at 3V |
Voltage Requirements
Comparison of Three Implementation Schemes for RTC Backup Batteries
Scheme 1:Non-Rechargeable Lithium Coin Cells
- Battery holder selection is far more important than it seems. Different manufacturers and different structures of battery holders result in vastly different contact reliability. During vibration testing, some inexpensive battery holders may experience momentary power interruptions, causing RTC resets. For equipment operating under vibration, it is recommended to fix the installed battery with adhesive during production and place a 0.1μF~1μF energy storage capacitor near the VBAT pin as a power buffer in case of contact interruption.
- Current-limiting resistors are essential. Direct Kurzschlüsse to the battery can cause it to explode. For example, the CR2032 has a maximum continuous discharge current of approximately 3mA. Assuming 3V, a 1KΩ resistor in series can limit the short-circuit current to within 3mA.
- Temperature affects battery life. The CR2032’s operating temperature is typically rated from -30℃ to +60℃, but its actual usable capacity significantly decreases below -10℃. Outdoor equipment using button cell batteries may experience clock hold failures in winter.
| Cell Type | Kapazität | Nominal / EOL Voltage |
| CR2032 | 220 mAh | 3.0V / 2.0V (EOL) |
| CR2025 | 165 mAh | 3.0V / 2.0V (EOL) |
| CR2016 | 75 mAh | 3.0V / 2.0V (EOL) |
| CR1225 | 48 mAh | 3.0V / 2.0V (EOL) |
| CR1220 | 35 mAh | 3.0V / 2.0V (EOL) |
Scheme 2:Supercapacitors
- High temperature adaptability: Typical operating temperature -40℃ to +70℃, far exceeding that of button batteries. They are practically the only choice for Automobilelektronik and outdoor instruments.
- Extremely long cycle life: Over 500,000 charge-discharge cycles, with a theoretical lifespan of over 10 years.
- No environmental disposal issues: Lithium-free, eliminating concerns about waste disposal compliance.
- Supports SMT-Löten: Direct reflow soldering is possible, eliminating the need for subsequent manual battery insertion and ensuring better process consistency.
Scheme 3:RTC Chip + Rechargeable Battery Combination
| Parameter | Primary Lithium Coin Cell | Supercapacit | RTC Chip + Rechargeable Battery |
| Rechargeable | Nein | Ja | Ja |
| Typical Voltage | ~3V | 2.5V–5.5V (varies) | ~3V (nominal, e.g., ML/VL series) |
| Operating Temperature | -10℃~+40℃ (usable area) | -40℃~+70℃ | depends on battery type |
| Self-Discharge Rate | Very Low (~1%/year) | High (5-20%/day) | Low (~1-2%/year) |
| Backup Duration | Long (years) | Short (hours to days) | Long (months to ~15 years) |
| Maintenance Requirement | Battery replacement needed | Minimal | Minimal (no replacement needed if regularly powered) |
| Design-Komplexität | Niedrig | Medium | Medium to High (needs charge management, power path) |
| Soldering Process | Rear-mounted battery holder | Supports SMT reflow soldering | depends on battery type |
| Kosten | Niedrig | Moderate to High | Moderate to High |
| Best Use Case | Long-term backup, devices rarely powered | Short-term backup, frequent charge cycles | Always-powered devices requiring long backup & no maintenance |
Key Design Considerations and Common Pitfalls of RTC Backup Battery PCBA
Diode Leakage Current
Current-limiting resistors
PCB Layout Design
Soldering Process
Real-World RTC Application
- Microcontroller-based embedded systems: Drive system clocks for real time in the absence of main power.
- IoT Devices: The sensors and smart home devices need to maintain the correct time in order to schedule events.
- Industriell Controllers: Store operational logs, timestamps, and process timing during power disruptions.
- Data Loggers: Records error-free timestamps for sensor data in use cases such as environmental tracking and medical devices
Why RTC Backup Battery PCBAs Require Professional PCBA Manufacturing Services
Leakage Current Control Assurance
Soldering Reliability
Component procurement
FS TECH's RTC Backup Battery PCBA Service Capabilities
End-to-End PCBA Manufacturing Capabilities
- Full BOM Komponente Beschaffung: Leveraging a global sourcing network, we ensure a genuine supply, competitive pricing, and stable delivery times for low leakage current Schottky diodes, branded supercapacitors (e.g., Murata, TDK, etc.), and original RTC chips (e.g., NXP, Microchip, IDT, etc.). We provide equivalent alternative solutions when items are out of stock.
- Integrated PCB Manufacturing and Assembly: From bare board manufacturing (supporting 1-58 layers, HDIund Hart-Flex-Platten) to SMT placement, DIP insertion, wave soldering, and post-soldering assembly, we provide a one-stop service, eliminating the need for multiple intermediaries for our clients.
- Professional process for matching RTC circuits: Double-sided SMT placement capability, minimum mountable 0201 package, BGA pitch 0.35mm. Extensive experience in assembling mixed-shaped components such as supercapacitors and battery holders. Strict adherence to IPC-A-610 Class 2/3 standards, 100% AOI optische Inspektion covering every PCBA, and Röntgeninspektion of BGA solder joints.
- Cleanliness assurance: Fully automated cleaning line removes flux residue; optional ion contamination testing for key products ensures that microampere-level leakage current circuits are not affected by board surface contamination.
- Funktionstests (FCT): Custom-designed RTC circuit test fixtures can be developed to measure critical parameters such as backup power switching waveform and VBAT current consumption before shipment, preventing defective PCBAs from leaving the factory.
Flexible Cooperation Models
Manufacturing Standards & Certifications
- Assembly Quality Standards: IPC-A-610 Class 2 / Class 3
- Quality Management System Certification: ISO 9001:2015
- Environmental Management System: ISO 14001:2015
- Environmental Compliance: RoHS / REACH / UL
- Industrieller Standard: IATF 16949 Automotive, ISO 13485 Medical
Fazit
FAQS about RTC Backup Battery
Verwandte Blogs
Table of Contents PCB Fuse Selection & Assembly: What Designers and PCBA Teams Need to Get Right Published on January 13, 2024 · Updated on
Table of Contents Medical PCBA Cost in 2026: What Really Drives the 2.5–4× Premium Over Commercial Boards Medical PCBA costs do not only depend on
Table of Contents PCBA Functional Testing (FCT): A Complete Guide to Ensuring Board Reliability Published on May 9, 2023 · Updated on November 6, 2026
Table of Contents IPC Class 2 vs Class 3: Acceptance Criteria, Cost Impact, and How to Choose IPC Class 2 and Class 3 are the
Table of Contents Ventilator PCB Assembly: ISO 13485, IPC Class 3 & FDA QMSR-Ready Manufacturing Published on June 24, 2022 · Updated on October 30,
Table of Contents Ventilator PCB Assembly: ISO 13485, IPC Class 3 & FDA QMSR-Ready Manufacturing How is air delivered steadily with the help of ventilators,
Wir würden uns freuen, von Ihnen zu hören